Cyclops Factory Upgrade Alarm Cyclops Factory Upgrade Alarm

Dynamco has upgraded the OE Upgrade, higher current immobilisation and multiple plug-in sensors available; to name only a few of the improvements. This Australian Standards Upgrade Alarm transforms an Original Equipment vehicle keyless entry system into an Australian Standards alarm system. The system is operated by the vehicles original equipment remote and has Entry point protection of doors, boot and bonnet with an intelligent glass break sensor. Audible warning is achieved via an Australian Standards 115dB battery back up siren, visually via the vehicle indicators and via a dash mounted red LED. The system has status / diagnostic reporting. The system can provide two additional circuits of immobilisation.

Proudly Australian - Designed and engineered in Perth, Western Australia.


  Operation
  • Arming procedure while ignition is off
     The system will arm immediately when the lock button of the remote control supplied by the car manufacturer is pressed.
  • Disarming procedure
     Press the unlock button of the remote control supplied by the car manufacturer.
  • Auto Arming feature
     System will auto-arm only if the car has a automatic re-locking feature Special feature out of Dynamco's control.
  Immobilisation
  • Two independent circuits of immobilisation
    30 Amp rated, normally open contacts.
  • Safety circuitry incase of power failure
    System sources alternate power from ignition if main power is lost.
  • Third circuit of immobilisation (optional)
    Additional immobilisation circuits can be added to conform with insurance company requirements Special order required - this is not part of the standard hardware..
  On-board relays
  • Protection against harsh road conditions
    All relays are fully encapsulated to provide protection against dust and moisture.
  Wiring
  • Security wiring
     All cables extending from the module are black and same diameter.
  • Plug and play for service
     Designed to allow easy access for service technicians.
  • Security housing
     Connector plug is enclosed within module case to prevent access by thief.
  • Stealth wiring
     Cutting any immobilisation wiring will still leave the car secure.
  Override
  • Emergency Personal Identification Number override
     Enter the secret four digits to override the immobiliser Feature is a programmable option.
  • Alterable PIN
     Users can change the numbers of their secret override PIN Feature is a programmable option.
  • High security keys and lock
     Disable siren sound when vehicle is taken in for service.
  • PIN card
     Secret override PIN is supplied on handy 90mm x 50mm card.
  Visual Output
  • Super bright red dash LED
     This LED flashes to inform user when system is armed. The LED is mounted on the driver's side dash and is visible from outside the window.
  • Arm/Disarm confirmation
     System flashes car indicators when arming or disarming Feature is a programmable option.
  • Alarm illumination
     System flashes car indicators when thief triggers alarm.
  • Trigger diagnostics
     System will flash indicators to report the last triggered circuit.
  Audio Output
  • Large battery backup siren
     AS/NZS 3749.1:2003 Class A approved 115dB siren, sounds even if battery terminals are disconnected from vehicle battery.
  • Negative siren output
     Can be used to trigger car horn relay or siren.
  • Arm/Disarm confirmation
     System sounds a siren when arming and disarming Feature is a programmable option.
  Intrusion Detection
  • Doors, bonnet and boot monitoring
     Triggers alarm system if intruder opens any protected entry point in vehicle May require additional hardware or connections.
  • False alarm prevention
     All circuits detected as triggered when arming system will automatically be isolated until trigger resets.
  • Sensor sockets
     Compatible sensors plug straight into main pcb.
  • Audio glass breakage detection
     Uses the sound of the breaking glass to trigger (not vibration) Will categorically need extra hardware and connections GBS-4XR.
  • Accepts plug-in Ultra-sonic sensor
     Sensor produces a 40KHz sound wave and measures echo to detect intruder, Will categorically need extra hardware and connections ACC-001.
  • Accepts plug-in single zone microwave sensor
     Sensor produces a microwave field to detect intruder, Will categorically need extra hardware and connections ACC-003.
  • Accepts plug-in dual zone microwave sensor
     Sensor produces two microwave fields, exterior field to sound siren as warning, interior to trigger alarm in full, Will categorically need extra hardware and connections ACC-004.
  • Accepts plug-in single stage shock sensor
     Sensor measures vibration subjected to vehicle to detect intruder, Will categorically need extra hardware and connections SEN-002.
  • Accepts plug-in two stage shock sensor
     Sensor measures two levels of shock, soft shock to sound siren as warning, heavy shock to trigger alarm in full, Will categorically need extra hardware and connections SEN-006.
  • Compatible with tilt sensor
     Sensor measures vehicle angle with respect to earth, triggers if angle changes - no response to vibration Will categorically need extra hardware and connections SEN-004.
  • Millivolt or Voltage drop protection
     Alarm monitors battery voltage, triggers if voltage drop due to courtesy light switched from off to on (opening boot etc) Feature is a programmable option.
  Specifications
  • Current draw
    <10mA average while armed
    <250mA disarm (and for no more than 39 seconds after ignition is switched off).
  • Operating voltage
    Operating voltage +9VDC to +15VDC.
  • Operating temperature
     -20 degrees to +85 degrees for equipment designed to be installed within vehicle cabin.
  • Polarity protection
     Accidentally reversing the battery leads will not damage the system.
  • Independent indicator power fuse
     System uses independent fuse to power indicators, ensures short circuit in indicator circuit does not affect system operation.
  • Short circuit protection
     Fuse protected in case any high power wiring is sheared through and shorted circuited.
  Convenience Functions
  • Electric window closer
     Provides signals used by electric window closers, system will close all electric windows when armed by remote control Will categorically need extra hardware and connections.
  • Full diagnostic report
     Remove and insert main power fuse to receive report of last three triggers.
  Printed Material
    Generic instructions on how to fit the system, it's features and limitations. Open Installation guide.
  • User Guide
     Informs the end-user of the system's functions, features and limitations. Open - User guide.
  Warranty
  • Manufacturers warranty on Control module
     Guarantees control module is free from manufacturing defects for 24 months from time of purchase Conditions apply.
  • Manufacturers warranty on Sundry items
     Guarantees remote controls, siren and sundry items are free from manufacturing defects for 12 months from time of purchase Conditions apply.
  Standards Compliance
  • Australian Standard for Intruder alarm systems - Road vehicles - Performance requirements
     AS/NZS 3749.1:2003 Class A - Australian Standards website.
  • Manufactured in ISO9001 facility
    Built within world standard production facility.
  • AS/NZS 3749 sundry standards of compliance (or parts thereof)
     AS1217 - Acoustics - Determination of sound power levels of noise sources
    AS1259 - Acoustics - Sound level meters
    AS1939 - Degrees of protection provided by enclosures for electrical equipment (IP Code)
    AS3350 - Safety of household and similar electrical appliances
    AS4268 - Radio equipment and systems - Short range devices
    AS/NZS3749 - Intruder alarm systems - Road vehicles
    AS/NZS61000 - Electromagnetic compatibility (EMC)
    CISPR 22 - Information technology equipment - Radio disturbance characteristics - Limits and methods of measurement
    ASTM B117 - Standard practice for operating salt spray (fog) apparatus
    ISO512 - Road vehicles - Sound signalling devices - Technical specifications
    ISO7637 - Road vehicles - Electrical disturbance by conduction and coupling
    IEC61000 - Electromagnetic compatibility (EMC).

NOTES LEGEND:
Will categorically need extra hardware and connections Will categorically need extra hardware and connections.
May require additional hardware or connections May require additional hardware or connections.
Additional relay and connection required in vehicles with boot solenoid. Relay and solenoid kit required for vehicle without solenoid Additional relay and connection required in vehicles with boot solenoid. Relay and solenoid kit required for vehicle without solenoid.
Vehicle circuit polarity may require addition components to convert voltage Vehicle circuit polarity may require addition components to convert voltage.
Special order required - this is not part of the standard hardware Special order required - this is not part of the standard hardware.
Special feature out of Dynamco's control Special feature out of Dynamco's control.
Conditions apply Conditions apply.
Feature is a programmable option Feature is a programmable option.
© Copyright 2007 Cyclops